ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.
|Published (Last):||8 January 2005|
|PDF File Size:||1.28 Mb|
|ePub File Size:||4.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
Current edition approved Sept. One bend test shall be made from one end of each coil. D PSS means plate, strip, sheet.
ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications. Maximum unless otherwise indicated.
Type L LN Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres. C Annealed material that naturally meets mechanical properties may be applied.
Only annealed conditions of grades speci? Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. Hard Elongation in 2 in.
ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
This revision of Speci? Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?
Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld. Due to the high a66610 hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part. These alloys represent an excellent combination of corrosion resistance and fabricability.
Permission rights to photocopy the standard may also be secured from the ASTM website www.
and L Stainless Steel – NKS
The choice of test method for materials in conditions other than annealed shall be zstm the option of the seller. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Your comments are invited either for revision of this standard or for additional standards and should be addressed a666-1 ASTM International Headquarters. HRC typical L Ann 25 min.
The values given in parentheses are for information only. The values obtained in this manner should not, however, be taken as the actual yield strength for 0. Last previous edition approved in as A — A — 10 Standard Speci?
Number of Tests 8. Rockwell B 95 95 Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: Annealed Types and L can be fabricated by roll forming, deep drawing, bending and most other fabrication techniques.
The noncontrolling factor normally will exceed considerably the speci? However, in the case of dispute, tests shall be made by pressure. Originally approved in Astmm standard has been approved for use by agencies of the Department of Defense.
Your comments astk receive careful consideration at a meeting of the responsible technical committee, which you may attend.
304 and 304L Stainless Steel
Material Test Report and Certi? Find out what NKS can do for you. Types and L are weldable by most fusion or resistance welding techniques.
Types and L cannot be hardened by thermal treatment. In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work. If you feel that your comments have not axtm a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. HardC Elongation in 2 in.