ECE R26 PDF

Regulation No 26 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with. ECE R26 Regulation (03 Series, ) “The uniform regulations on vehicle chapter and section numbering betw een this standard and the ECE R ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL OF: VEHICLES WITH REGARD TO THEIR EXTERNAL PROJECTIONS Incorporating.

Author: Akigami Mazugis
Country: Serbia
Language: English (Spanish)
Genre: Environment
Published (Last): 6 February 2008
Pages: 357
PDF File Size: 16.44 Mb
ePub File Size: 16.8 Mb
ISBN: 295-3-49588-479-6
Downloads: 75040
Price: Free* [*Free Regsitration Required]
Uploader: Akinohn

Revision When particulars recorded in the information folder have changed and the Type Approval Authority considers that the modifications made are unlikely to have an appreciable adverse effect and that in any case the vehicle still complies with the requirements, the modification shall be designated a “revision”.

This date signifies when the text legally becomes part of the international approval system i. Tyres taken from normal series production with the minimum nominal section width and minimum rolling circumference on the range of tyres recommended for the particular wheel. UN R45 Headlamp Cleaners. These provisions shall not apply to ornaments on radiator grilles, to which only the general requirements of paragraph 5 shall apply.

Conformity of Production 9. Application for approval of a vehicle type with regard to its external projections.

– Transport – UNECE

In the case where negative results are recorded during one of these visits, the competent authority shall ensure that all necessary steps are taken to re-establish the conformity of production as rapidly as possible.

Retracting headlights shall meet the provisions of paragraph 6. Handles, hinges and push-buttons of doors, luggage compartments and bonnets; fuel tank filler caps and covers 6. With regard to the design, inset, rim designation wheel fixing PCD and spigot mounting diameter, correspond to that of an OE-wheel, but wheel contour, material and so on, may be different. Type I — Fade test procedure.

The second phase efe the development of this regulation by the Child Restraint Systems informal working group is underway to extend the scope of this regulation to include ISOFIX non-integral universal booster seats. In the case of a failure further samples shall be tested. UN R Cornering Lamps.

EUR-Lex – X(08)R(01) – EN – EUR-Lex

The nominal rim diameter, nominal rim width and nominal inset of ECE-approved wheels shall be the same as the manufacturer’s replacement wheel. A surface treated sample, taken from production, shall be damaged by cross engraving and stone impact ISO to represent damaging situations during the normal usage of vehicle damage shall be in the area of the rim flange and inside the wheel.

  COMPUTER BASED INDUSTRIAL CONTROL BY KRISHNAKANT PDF

In some cases, the provisions permit extensions of current approvals based upon rr26 requirements for example, to allow for replacement parts. All InterRegs documents are formatted as PDF files and contain the full text, tables, diagrams and illustrations of the original as issued by the national government authority.

The surface treated sample shall pass a salt-spray test, in which the sample and any components with which is normally in contact are put in upright position into the salt-spray test equipment. Of side direction indicator lamps, end outline marker lamps, front and rear position side lamps and parking lamps; 2.

The type approval authority shall be supplied with a copy of following information which shall also be supplied to the consumer with the wheel. If the process within a production line is always the same, only one representative test is to be carried out. Drawings of the necessary sections through the external surface shall be provided by the manufacturer to allow the height of the projections referred to above to be measured.

Eece of markings which shall be applied to a wheel conforming to this Regulation:. Dependent upon the particular vehicle the floor line trace may occur at the bumper section extremity or at the eec panel below the bumper.

Licenses and Certificates

The basic number of wheel fixings, for example 4 holes, 5 holes and so on, shall not be changed. Uniform Provisions Concerning the Approval of Filament Lamps for Use in Approved Lamp Units of Power-driven Vehicles and of their Trailers UNECE R37 specifies technical and administrative requirements for the approval of a wide range of filament lamps shown in Annex 1 of the regulation that are intended for use in approved lamp units of power-driven vehicles and of their trailers.

Agricultural vehicle couplings Mechanical coupling components for agricultural vehicles UN Regulation No. Characteristics of the separate technical unit: EU case law Case law Digital reports Directory of case law.

UN R75 Motorcycle Tires. Uniform provisions concerning the approval of vehicles with regard to the emission of pollutants according to engine fuel requirements Fuel Consumption Measurement Measurement of Passenger Car Fuel Consumption UN Regulation No. One in the area connecting spokes to rim and further one in the area between two spokes, very close to the valve hole. One for each impact position.

  DEMYSTIFYING PATANJALI PDF

As a rule, the following criteria have to be fulfilled: The administrative department which has granted approval of the vehicle type shall be notified of any modification of the vehicle type.

The Type Approval Authority shall verify r6 existence of satisfactory arrangements for ensuring effective control of the conformity of production before type approval is granted. Limitations of use, if any, and assembly instructions: UN R23 Rce Lights. There shall be affixed, conspicuously and in a readily accessible place ecw on the approval form, to every separate technical unit conforming to a type approved under this Regulation, an international approval mark consisting of: Where this is not possible, an equivalent method shall be used.

If the holder of the approval completely ceases to manufacture the type approved in accordance with this Regulation, he shall so inform the authority which granted the approval. The same Contracting Party may not assign the same number to another type of wheel.

Production definitely discontinued Windows which move outwards from the external surface of the vehicle eve comply with the following provisions in all positions of use: Regarding wheel bolts, nuts and studs, the length of thread engagement shall be the same as achieved by the vehicle manufacturer’s replacement wheel and wheel fixings. The regulations are also designed for use within the international approval system. Added ornaments which project more than 10mm from their support shall retract, become detached or bend over under a force of 10daN exerted at their most salient point in any direction in a plane approximately parallel to the surface of which they are mounted.

Check of the mechanical characteristics R p0,2R mand A of test-pieces taken from the hub mounting area and in the disc to rim transition area or in the failure cee if any. UN R41 Motorcycle Noise.

The rim and wheel disc may be integral, permanently attached, or rce. The dimension of the projection of a component which is mounted on a convex surface may be determined either directly or by reference to a drawing of an appropriate section of this component in its installed condition.